Home » Electrical Engineering » CONSTRUCTION AND DESIGN OF BATTERY LEVEL INDICATOR CIRCUIT

CONSTRUCTION AND DESIGN OF BATTERY LEVEL INDICATOR CIRCUIT

Sold By: Samson Timi | Item Type: Project Material | Report this?  |  Attributes: 31 pages | 6 chapters | Amount: ₦5,000 | 27 orders. | Marked useful: 20,988 times

INSTANT PROJECT MATERIAL DOWNLOAD

ABSTRACT

Technology on batteries has advanced over the years as a result of the need to power portable devices that have risen in numbers in the last decade. Just like primary cells, rechargeable batteries work in the same way, only their chemical reactions are reversible. This project aimed at building a system that would indicate the capacity level of a Nickel Metal Hydride battery upon charging and discharging. The Nickel Metal Hydride battery was selected in this project due to its preference among consumers. However, since the principle behind the rechargeable battery technology is similar, the system can be used to test other types of batteries. System implementation involved designing and building a battery charger circuit and a discharge circuit. Software design then followed, after which testing was performed. The project uses a LM3914 driver IC use to drive 10 leds by passing through it sufficient amount of current. Brightness of leds are controlled by reference adjustable pin and reference out pin. The project goal was achieved and results were presented through numeric figures, charts and indicators. The system is expected to help in planning with batteries to avoid halt of devices during operation. The results gathered during testing point to possible reduced battery wastage. A better way to handle batteries to conserve capacity has also been highlighted.

CHAPTER 1

INTRODUCTION

1.1 PROJECT OVERVIEW

Battery level indicator is a circuit that is used to check the battery life. We can easily recognize the battery level with the help of LED’s. It uses a LM3914 driver IC use to drive 10 leds by passing through it sufficient amount of current. Brightness of leds are controlled by reference adjustable pin and reference out pin. A variable resistor is also deployed in the circuit to have variable input voltage at pin 5 of the driver IC. Since the driver IC has two modes of operation which is bar graph mode and dot mode, it enables us to have indication of the battery life either in bar form or in dot form. We can have colouredlods to indicate state of the batteries like first three leds will indicate low battery. Green leds will indicate full battery. Thus by using various colouredleds representation of battery life will be made easy to understand. Cascading the driver ICs we can increase the range of battery input in terms of voltage. In the below given block diagram we have 4 blocks. One is the power supply. other is the driver IC itself. We will have a led block and an input block. A reference input for comparison purpose. Leds will glow according to the input given and the reference Input present.

Power supply is ranging around 12 to 18V. Reference voltage is pre decided which is 1.25mV. Any dc signal lying in the range of the power supply is judged and the level is indicated by the leds. The current through the leds is controlled by the internal adjustment.

2 The battery level indicator consists of very less component and thus occupies very little space of the surrounding. Since only DC input voltage levels are indicated, components which work in AC supply can be used to detect AC levels. Since AC voltage having continuously varying amplitudes the leds will turn ON and OFF continuously making a good looking pattern. Thus our battery level indicator can be used for decoration purpose also.

1.2 ADVANTAGES

v A battery level indicator is with electronic appliances to arrange as to display, on an indicator, a real time voltage detected by voltage indicator.

v Indicator indicates how much power the battery will be able to supply to electronic apparatus.

v It is used to check the battery level with the help of LED’s for example if three LED’s, indicates battery capacity of 30 percent. And if 10 LED’s glow then it is 100 percent.

v Easily indicate the battery level

v Enhanced version of this circuitry is the present mobile phone battery level indication system

v This circuit can be used in household applications like INVERTER. This circuit connected to inverter can help the users to know when to charge and when to leave the inverter idle

v Minimized version of this circuit can be also used for automobiles to indicate the battery level and low cost.

1.3 DISADVANTAGES

v In case of voltage matching, correct level wouldn’t be indicated

v 1f input voltage is higher than the calibrated voltage, for full scale input error will be shown.


This material content is developed to serve as a GUIDE for students to conduct academic research



DOWNLOAD THIS PROJECT MATERIAL NOW!

  • Reference(s):

    Messenger, R. A. and Ventre, J. (2000).Photovoltaic Systems Engineering. New York: CRC Press, 2000, pp.63-64, pp. 53, 64, 297-303 Messenger, R.A. &Ventre, J. (2004).Photovoltaic Systems Engineering. New York: CRC Press LLC. National Lighting Product Information Program, (2005).Lighting Research Center, NLPIP Lighting Answers, “Photovoltaic Lighting”, 9 (3). Northeast Sustainable Energy Association, NESEA, (2001).Solar Electricity. Retrieved 5th June 2016. from http://www.nesea.org/buildings/info/solarelectricity.html

  • Methodology: get complete material to enable


Advertise Here

For advertisement, call 08168958821

Not what you were looking for? Perform a search

What's your project topic?


Comment on Facebook: